Experience clean, high quality drinking water every time you turn on the faucet and crystal clear ice cubes, scum-free tea and coffee. Designed for safer, healthier water. The system uses tried and tested NSF certified components. Removes up to 99% of over 1,000 contaminants and is ideal for homes, fitting neatly inside an under sink kitchen cupboard or up to 5/10 metres away with additional tubing if needed. Easy installation and maintenance with Plug & Play parts.
- Under counter mounted water filtration system for ease of use.
- Removes up to 99% of over 1,000 contaminants including: lead, chlorine, fluoride, arsenic, heavy metals, asbestos, hardness, sodium, microorganisms and much more.
- Experience clean, high quality drinking water every time you turn on the tap and crystal clear ice, scum-free tea and coffee.
- Premium packaged filters with 6-12 months filter lifetime. High quality components with NSF certification.
- Easy installation and maintenance with Plug & Play parts.
- 10 litre total capacity tank (6 litres ready for instantaneous use).
Easy installation and Filter Changes
The system comes with an installation ready kit except for a handful of standard DIY tools and can be installed by a competent DIYer or plumber.
Pre-Filtration (Stage 1, 2 & 3) – recommended change every 6-12 months
Pre-filter lifetime can be reduced as a result of the level of turbidity and sediment in the feed water. The BMB HP-105 LX Reverse Osmosis System uses high performance pre-filters. Although the pre-filters used in this system are fully efficient in removing chlorine and sediment, they do much more.
First, the pre-filters for this system will remove sediment down to 0.5 microns which will more thoroughly protect the RO membrane.
Second, the pre-filters use coconut shell powder carbon instead of granule or block carbon (used in traditional systems) which has up to 10 million times more surface area for greater absorption rates and much longer lifetime.
Third, the pre-filters in this system are also designed to reduce heavy metals such as iron, manganese and rust which can also damage the RO membrane.
Reverse Osmosis Membrane (Stage 4) – recommended change every 12 – 36 months
Reverse Osmosis is the most advanced technology of water purification in use today. The technique uses a nanotechnology enabled semipermeable membrane which can reduce or remove most harmful impurities found in tap and well water including: microorganisms, nitrates, heavy metals, fluoride, insecticides and much more. The BMB HP-105 LX uses the industry leading, USA made, DOW Filmtec Membranes for solid reliability and performance. The double o-ring housings ensure no leaking problems, filters and pump and other components are made in Taiwan with top end manufacturing quality with NSF certification.
The table below lists the performance of specific contaminants. This is only a partial list of the virtually hundreds of thousands of contaminants that Reverse Osmosis can filter.
Estimated Reverse Osmosis Rejection Percentages * Figures given above are estimates of normal performance, under normal conditions and water.
At the heart of every Reverse Osmosis system is the membrane filter. The membrane filter consists of microporous, semipermeable membrane sheets. The average pore sizes on the RO membrane is in the range of 0.0005 mm (0.5 nanometers). The membrane filter has one water inlet and two exits. The feed water first travels through the pre-filters and then to the membrane filter.
At the exit of the membrane filter one of the ports is the rejected waste water which is connected to the drain, while the other port is the purified water which is plumbed to the post-filters.
We recommend membranes are changed no longer than every 3 years or when the TDS reaches over 50ppm.
Post Filter (Stage 5) – recommended change every 6-12 months
The Post Filter is an NSF Certified Activated Granular Coconut Shell Carbon: NSF.
This coconut shell carbon that acts as a final polisher and mineraliser.
Fitting it to your kitchen:
This system can easily be installed by a handy person or plumber and the kit contains all essential parts and some of your own DIY tools are required.
Before ordering please ensure your incoming water pressure exceeds 1.8 bar. Please note the system and tank dimensions below. RO system and tank can be sited up to 5-10 metres away if necessary from the tap.
The system fits neatly inside a standard 500-600mm kitchen cupboard but if you other appliances such as waste disposal, please check to see if it will fit first.
System Dimensions (L x W x H) 40 cm x 17 cm x 44 cm
Tank Dimensions (L x W x H) 24 cm x 24 cm x 37 cm